craigmc67 Posted March 12, 2022 Share Posted March 12, 2022 Just fixed the water temperature gauge on my broom robb, it has a nanni 4 150 he. the water temperature gauge is running at approximately 90 degrees c and at points it a bit higher dose that sound about right or a bit hot ? Quote Link to comment Share on other sites More sharing options...
BrundallNavy Posted March 12, 2022 Share Posted March 12, 2022 A bit hot I would say. 1 Quote Link to comment Share on other sites More sharing options...
Vaughan Posted March 13, 2022 Share Posted March 13, 2022 The 4150 is an early engine, which conformed to Italian horsepower limits on hire craft. Does it have the word KUBOTA pressed into the top of the rocker box? They do run fairly hot - but 90 is a bit high. They depend on a pressurised water system, so check that the pressure cap is in good order. Also a good idea to take out the tube stack in the heat exchanger and check the tubes are not furred up. A couple of days immersed in vinegar can make a big difference. Obviously also check the condition of the raw water pump and ensure there is a good flow of water coming from the exhaust. If there is a long delay when starting, before water comes out, then you have a pump problem. Do NOT take off the water pressure cap when the engine has been running and is still warm. There is a lot of pressure in there! 2 1 Quote Link to comment Share on other sites More sharing options...
craigmc67 Posted March 13, 2022 Author Share Posted March 13, 2022 Thanks I’m taking her for a little trip from Beccles to oulton broad so will check everything out is the away to check the the actual water temperature say using a probe ? Quote Link to comment Share on other sites More sharing options...
Vaughan Posted March 13, 2022 Share Posted March 13, 2022 15 minutes ago, craigmc67 said: is the away to check the the actual water temperature say using a probe ? In my experience, an electric water temp. gauge either shows the correct temperature, or it doesn't work at all. In the early days of Crown Blue line we did have problems with overheating on the Nanni 4150 and 4190. After research with Peachments, we fitted a larger Jabsco raw water pump. If the problem persists, talk to Peachments as they are the Nanni agents and have a lot of experience of the problem. Ask for Andrew Peachment and give him my kind regards! 1 1 Quote Link to comment Share on other sites More sharing options...
BrundallNavy Posted March 13, 2022 Share Posted March 13, 2022 You can cross check with a IR thermometer or as I have used a meat probe. 1 Quote Link to comment Share on other sites More sharing options...
Smoggy Posted March 13, 2022 Share Posted March 13, 2022 With an IR thermometer don't point it at a shiny bit of engine or you'll get a duff reading, a nice matt black hose is the ideal spot to check, they are dirt cheap off fleabay. 1 Quote Link to comment Share on other sites More sharing options...
JanetAnne Posted March 13, 2022 Share Posted March 13, 2022 It may just be a slight mismatch between your Nanni sender and Durite gauge Craig. Probably worth getting the sender parameters from Peachments and compare with the Durite input range. That engine didn't show any signs of having been too hot previously 1 Quote Link to comment Share on other sites More sharing options...
Smoggy Posted March 13, 2022 Share Posted March 13, 2022 A crappy connection somewhere with a bit of extra resistance would make a european gauge read higher, a USA gauge would read lower with the same issue, if you disconnect the sender the gauge will likely go to the very top. 1 Quote Link to comment Share on other sites More sharing options...
craigmc67 Posted March 13, 2022 Author Share Posted March 13, 2022 Thanks I will call them Monday, I have used them before and always found them very helpful especially Brian in the technical department Quote Link to comment Share on other sites More sharing options...
craigmc67 Posted March 13, 2022 Author Share Posted March 13, 2022 2 hours ago, JanetAnne said: It may just be a slight mismatch between your Nanni sender and Durite gauge Craig. Probably worth getting the sender parameters from Peachments and compare with the Durite input range. That engine didn't show any signs of having been too hot previously We can check it out tomorrow Dave I will bring a temperature probe it doesn’t appear to be running hot Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.