diesel falcon Posted January 14, 2015 Share Posted January 14, 2015 Hi, although our boat was built in the 90,s it has some quiet nice teak veneers ,the problem i ve got is with the table, it has had a black/dark patch, where the front hatch used to leak since we bought the boat, , is there anyway i can bleach it out or is it terminal? Quote Link to comment Share on other sites More sharing options...
Guest Posted January 14, 2015 Share Posted January 14, 2015 Oxalic acid will bleach it out, the tricky part is in then recoating it without the varnish soaking in unevenly into the area dried out by the acid. You need to first seal the surface with something that doesn't soak in and darken the wood more than the surrounding area. I was successful with International's "UCP" primer a few times, but it's tricky to be consistent. Quote Link to comment Share on other sites More sharing options...
Liberty Posted January 14, 2015 Share Posted January 14, 2015 I am absolutely no expert by any stretch of the imagination, but I have heard you can use oxalic acid for this kind of thing. Late again..!!! Quote Link to comment Share on other sites More sharing options...
quo vadis Posted January 14, 2015 Share Posted January 14, 2015 This should be in restorations Quote Link to comment Share on other sites More sharing options...
ranworthbreeze Posted January 14, 2015 Share Posted January 14, 2015 On this site there is a few tips to try out, before you go the whole hog and have to totally strip down the surface of the table top.http://cleaning.lovetoknow.com/Remove_Water_Stain_from_WoodTo be honest I think you will have to strip the table, treat the stain and then re-polish.RegardsAlan Quote Link to comment Share on other sites More sharing options...
diesel falcon Posted January 14, 2015 Author Share Posted January 14, 2015 Thanks all........and blunt que Quote Link to comment Share on other sites More sharing options...
wombat nee blownup Posted January 15, 2015 Share Posted January 15, 2015 Take it to Jiffy. He'll DA it down as far as you like and re lacquer it. It'll end up green or some such colour but hey! it'll match the colour of your canopy Quote Link to comment Share on other sites More sharing options...
650xs Posted January 15, 2015 Share Posted January 15, 2015 for the best results to address this use a very good french polisher who knows his onions they can do this easy and match it etc it that filed the antiques trade know what to do how to sort out such issues all sort sorts chemical like proper wood bleaches to oxalic acid then pigments to correct colours, sealer from single pack/two pack .alchol based ,water based and pre cat types etc etc grain filler ,woode sealer ,selalc sealer coloured and self colours to oil varnish s heat rest sellers and both and all types or lacquers gloss to semai matts etc etc etc arghh phew the list goes on and on..................bored now ........... if yer want it rite use the man who can if yer want a risk and do it yer self if yer wiling to give it a goo do it ,if yer want it rite ...................nooo diy ...don,t envolve yer self ................ either way let us know how yer get on as we all like to hear the out come of all stories and info ....wel i do...................orf to work bye.. 1 Quote Link to comment Share on other sites More sharing options...
ExSurveyor Posted January 15, 2015 Share Posted January 15, 2015 It's called Blue stain in service, and is a pig to get out, get an expert to have a go as it may be quite deep and need a fair amount of sanding if a french polisher can't get it out. The wrong process of chemicals could make the stain much harder to deal with for the expert. Quote Link to comment Share on other sites More sharing options...
diesel falcon Posted January 15, 2015 Author Share Posted January 15, 2015 Progress report! i ve stripped the table top with nitromoors , it,s revealed a coffin blow for the finish , the water has rotted the veneer to the point that a small amount of it was missing altogether! i think i need a rethink! it may even get painted, or sticky back plastic!! Quote Link to comment Share on other sites More sharing options...
ranworthbreeze Posted January 15, 2015 Share Posted January 15, 2015 Hello Diesel Falcon, It might be an idea to remove the old veneer and replace with a new veneer sheet/sheets, not for the faint hearted but if your boat does have a lot of teak it may be worth it. I would try to remove it with a damp cloth and iron or a steam iron, the idea is to soften the glue that is holding the veneer in place. You could of course try using some wood bleach to get a more uniform colour and then fill the missing veneer with some wood stopper (teak if you can find it) . If you can get a good overall colour then you can stain it and give the top a polish. I have had very good results with many thin coats of Danish Oil allowing to dry between each coat. Regards Alan Quote Link to comment Share on other sites More sharing options...
ExSurveyor Posted January 15, 2015 Share Posted January 15, 2015 You could try to patch the damaged veneer or be really adventurous and re veneer the whole top. Can't make it look worse Quote Link to comment Share on other sites More sharing options...
diesel falcon Posted January 15, 2015 Author Share Posted January 15, 2015 It,s a very thin machine applied one so i,ll think of something, re veneering it would be too expensive for what it is,a kitchen worktop finish might look ok,as the sink/cooker and cupboard top have a pinkish one fitted Quote Link to comment Share on other sites More sharing options...
Guest Posted January 15, 2015 Share Posted January 15, 2015 If it's that far gone, it may be simpler and better to accurately cut a new top from teak faced marine ply. It should be possible to remove the original edge mouldings and transfer them to the new piece. Tim Collin at Hoveton stocks a very wide range of sheet materials and hardwoods, teak, mahogany, cherry etc., and is the local supplier to many very high quality boat building firms. He's still very approachable though, gives great advice, and will happily sell a single sheet, searching through the stack with you. It will have to be a full 8x4 sheet, but probably cheaper overall than employing a skilled professional restorer, and the rest of the sheet may come in useful with the boat. A few years back I replaced the internal cabinet work in a wheelhouse using a sheet of teak faced 15mm marine ply from him, it cost over £60, but it was a beautiful piece of wood, and transformed the interior. Quote Link to comment Share on other sites More sharing options...
BroadScot Posted January 15, 2015 Share Posted January 15, 2015 I love teak wood, I think it was all the years wiring the display stands for G-Plan, in a local furniture store in Ayr. A nice piece of grained Teak is something to admire IMHO. Iain. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.