Maxwellian Posted November 6, 2017 Share Posted November 6, 2017 11 hours ago, grendel said: another pair of planks have gone in. Any of those Short ones Grendel? Only takes two! 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 6, 2017 Author Share Posted November 6, 2017 tonight has seen 2 more planks in, another 2 and the posh planks can be applied 1 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 6, 2017 Share Posted November 6, 2017 Posh? Don't know about that but they are made of the right stuff! You got enough for the cabin sides? Port Out Starboard Home Griff Quote Link to comment Share on other sites More sharing options...
grendel Posted November 6, 2017 Author Share Posted November 6, 2017 I have only used the smaller of the long bits so far, about 1 1/2" x 1 1/2" I still have the bigger bit for the cabin sides and other bits, that will be cut wider to be able to do the full height of the sides out of one 'plank' also slightly thicker than the planks for the transom. the teak really does come up nice when cut and sanded. 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 6, 2017 Author Share Posted November 6, 2017 as the teak is a quite oily wood, it will be cleaned with acetone just prior to applying glue, this will give the glue the best chance of sticking properly. 1 Quote Link to comment Share on other sites More sharing options...
Wildfuzz Posted November 7, 2017 Share Posted November 7, 2017 9 hours ago, grendel said: as the teak is a quite oily wood, it will be cleaned with acetone just prior to applying glue, this will give the glue the best chance of sticking properly. What glue are you going to use as I always struggle with teak..... is it the Gorilla stuff? Quote Link to comment Share on other sites More sharing options...
grendel Posted November 7, 2017 Author Share Posted November 7, 2017 yes, clean with acetone, light mist of water, and then glue, clamp firmly, the gorilla glue migrates into the structure of the wood and absorbs water to bond, thats why the cleaning to remove surface oils. 2 Quote Link to comment Share on other sites More sharing options...
KaptinKev Posted November 7, 2017 Share Posted November 7, 2017 11 hours ago, grendel said: yes, clean with acetone, light mist of water, and then glue, clamp firmly, the gorilla glue migrates into the structure of the wood and absorbs water to bond, thats why the cleaning to remove surface oils. Gorilla glue, is that American? I would of thought that this build would solely be built on English tradition and not include crappy import nonsense. 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 7, 2017 Author Share Posted November 7, 2017 well we could use cascamite, but it takes forever to set, then goes brittle - or that smelly stuff in a pot you heat up. nah, I will go with the gorilla thanks, anyway tonight its the last 2 awkward transom planks, they are in place and setting. 4 1 Quote Link to comment Share on other sites More sharing options...
SteveO Posted November 8, 2017 Share Posted November 8, 2017 Good old hoof and horn or rabbit skin glue is what you need. Stinky and not very good, but traditional. If these haven't been invented by the British yet, you may have to resort to fastening the wood with little oak pegs. 1 1 Quote Link to comment Share on other sites More sharing options...
Guest Posted November 8, 2017 Share Posted November 8, 2017 16 minutes ago, SteveO said: Good old hoof and horn or rabbit skin glue is what you need. Stinky and not very good, but traditional. If these haven't been invented by the British yet, you may have to resort to fastening the wood with little oak pegs. Its stinky alright , you have just reminded me of my apprenticeship my first job in the morning was get the glue pot on , came in a bead format if I remember rightly and absolutely stunk and very brittle when cured . Quote Link to comment Share on other sites More sharing options...
grendel Posted November 8, 2017 Author Share Posted November 8, 2017 didnt have rabbit skin glue until the romans introduced the bunnies. 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 8, 2017 Author Share Posted November 8, 2017 excess planking and spare thumb trimmed off the transom of the model yes I slipped with the saw and sliced my thumb, nice sharp mini japanese style saw. 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 8, 2017 Author Share Posted November 8, 2017 Still not letting my sliced thumb stop me working, I went ahead and sanded the transom, just a little skim to fill in the joints, and then I can start fixing the decorative teak transom. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 8, 2017 Author Share Posted November 8, 2017 small amount of filler mixed up and applied across the transom to fill any small gaps prior to fixing the decorative wood, left out in the worksop to cure, it will be sanded flush tomorrow, then I can get on with the pretty stuff. 3 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 9, 2017 Author Share Posted November 9, 2017 filler sanded down while my dinner was cooking, ready for pretty planks now 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 9, 2017 Author Share Posted November 9, 2017 so after scoffing my tea, and posting here a bit, it was back out to the fray, the edges needed straightening, so I tried planing it - horrible, the belt sander finally got 4 pieces straight to each other. These were marked so I knew where to line them up. and then the first piece was given an acetone wipe, allowed to dry, then both sides of the joint were spritzed with a mist of water, glue was applied and spread, and using packers to protect the wood from the clamps it was clamped in place, it will now sit until tomorrow night clamped up. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 10, 2017 Author Share Posted November 10, 2017 second transom plank this evening. 4 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 10, 2017 Share Posted November 10, 2017 Looking good there Pete, I see that you will use about four planks for the transom, on the real thing there must be about 12 separate horizontal planks - No don't even think about changing them! Cant wait to see them flatted off, (320g) then varnished. What varnish do you intend to use? Brava as on 'B.A' gives a cracking high depth gloss finish, shall I order you some? Griff Quote Link to comment Share on other sites More sharing options...
grendel Posted November 10, 2017 Author Share Posted November 10, 2017 I'm not going to need a vast amount Charlie, if you have some left over in a tin, it will probably be enough. 1 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 10, 2017 Share Posted November 10, 2017 I'll get a tin sent to you along with some pure turpentine (Not the substitute stuff) with my method of application etc. Oh and I'll get some genuine 'Purdy' brushes to you as well Griff 1 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 11, 2017 Author Share Posted November 11, 2017 the third plank went on this morning, after each plank I have to clean up the squeeze glue as it expands on curing, before prepping the next plank. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 11, 2017 Author Share Posted November 11, 2017 the fourth plank is on, tomorrow we will be ready to start sanding 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted November 12, 2017 Author Share Posted November 12, 2017 So this morning after a fruitful boot fair visit, and doing all of the remaining weekend chores, it was back to the transom, off came the clamps, and then to work, 60 grit on the electric sander, followed by 100 grid on a sanding block, I then worked through 120 grit, 150 grit, a long time on 400, as I dont have anything between, then 600, 800 and 1500 grit, finishing off with a 3000 grit finishing cloth, well I dont know about you, but when its already reflecting the flash, and its not even varnished yet, I call that a result. the wood was chosen to have some nice grain detail. 5 2 Quote Link to comment Share on other sites More sharing options...
Wonderwall Posted November 12, 2017 Share Posted November 12, 2017 Looks fantastic. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.