Baitrunner Posted November 6, 2016 Share Posted November 6, 2016 Apart from the illustrious Mr Griff, does anyone have any top tips on removal a few tiles? we had an old floor standing boiler which was replaced last week for a walk mounted one. I now have 4 tiles that had been cut to go around the old boiler that i need to remove. I also have 4 spare tiles to replace these with, so zero room for errors. I have never had to do this so need to get it right. I have a grout remover tool which doesn't look like it will be too helpful. The grout and adhesive does seem to be very hard, but isn't concrete. It was proper tile adhesive. I was thinking if a dremel with a fine cutting disc to make sure the grout was completely removed before I try and remove the old tiles. Does this sound like it will work or should I just buy a rug? any help gratefully received. Quote Link to comment Share on other sites More sharing options...
quo vadis Posted November 6, 2016 Share Posted November 6, 2016 Turf it Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 6, 2016 Author Share Posted November 6, 2016 Thanks Q. That just means more grass to cut Quote Link to comment Share on other sites More sharing options...
JennyMorgan Posted November 6, 2016 Share Posted November 6, 2016 A smack with a bolster should crack it. Quote Link to comment Share on other sites More sharing options...
imtamping2 Posted November 6, 2016 Share Posted November 6, 2016 I'm with JM on this one angle the bolster at the top of the tile toward the wall and give it a crack with a Hammer/Bolster....... Quote Link to comment Share on other sites More sharing options...
grendel Posted November 6, 2016 Share Posted November 6, 2016 I also am an exponent of the bolster, but would defer to Griff's advice. Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 6, 2016 Author Share Posted November 6, 2016 Picture so you can see that the offending tiles are surrounded by good tiles. Hence going at it with the hammer and bolster was a little concerning!! Quote Link to comment Share on other sites More sharing options...
JennyMorgan Posted November 6, 2016 Share Posted November 6, 2016 GRIFF - HELP! Quote Link to comment Share on other sites More sharing options...
imtamping2 Posted November 6, 2016 Share Posted November 6, 2016 Ahaaaaaa Floor !!!!!!! I assumed wall...........now what was it about assume.....I remember.. I would dremmel grout and adhesive from around tiles and then bolster. 1 Quote Link to comment Share on other sites More sharing options...
JanetAnne Posted November 6, 2016 Share Posted November 6, 2016 Had a very similar problem when I dropped something sharp and heavy right in the middle of our dining room floor chipping a chunk out of the tile of course. I got the angle grinder with a thin stone disc and cut the damaged tile into sections that then easily broke away without disturbing the surrounding ones. 3 Quote Link to comment Share on other sites More sharing options...
Jbx5 Posted November 6, 2016 Share Posted November 6, 2016 Hi Mark best not to use a grinder in the house as a major dust problem best option bolster or cold chisel as gentle as possible to chip away the tiles you need to remove. John 1 Quote Link to comment Share on other sites More sharing options...
ZimbiIV Posted November 6, 2016 Share Posted November 6, 2016 I suggest fill the gap with your spare tiles, then park a nice butchers trolley over the top of it. paul Quote Link to comment Share on other sites More sharing options...
kfurbank Posted November 6, 2016 Share Posted November 6, 2016 DeWalt Multi tool if you have access to one is by far the best bet. Cut along the grout line first and then a chisel under the tiles that are coming out. Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 6, 2016 Author Share Posted November 6, 2016 all. Yep the angle grinder is out. Been there and seen the mess on other projects Thought the dremel might be a lighter touch though. I can also probably rig a dust extractor up to keep the mess down. I have a large dust collector for the table saw that can be hooked up to routers etc could get it near my work area. My problem is patience. Or lack of it think I have a plan now, pending any revelations from the Griff! Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 6, 2016 Author Share Posted November 6, 2016 Don't have a multi tool - yet. Might need one now though Quote Link to comment Share on other sites More sharing options...
grendel Posted November 6, 2016 Share Posted November 6, 2016 good excuse to buy one though 1 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 7, 2016 Share Posted November 7, 2016 Apart from the illustrious Mr Griff, does anyone have any top tips on removal a few tiles? Why? - Should have been obvious to ask me direct in the first place I would have thought Sorry for delay, - had a proper full day. got collected at 0830 this morning, driven up to near to Carlisle to do a huge estimate, then back to Donny, home for 1700. Then off to one of my local farmers (Where our syndicate shoot is run from) to reload his huge commercial wood burner (They are away for the weekend), got it filled and running only to discover one of the pumps not working, took me well over an hour to sort that one out. Then out with MrsG for dinner. then 2 x hrs trying to get the estimate typed up (Still not finished) 2130 off to the pub with the lads now home after having walked the hounds. Ok tile removal (Same for floors and walls) without damaging the neighbouring tiles Standard angle grinder with a fine diamond blade (Designed for use with ceramics / porcelain etc), safety glasses, henry hoover with plastic clevis tool. Close internal doors to rest of house, open windows and or external door if there is one. Keep clevis tool close the back of the blade then using angle grinder run it along the grout lines of the tiles to be removed down to a depth just below the bottom of the tiles. Hammer - smack the tiles hard, then with sharp old wood chisel and hammer if needed remove the tiles in pieces. Then again with sharp old wood chisel, VERY carefully and GENTLY remove remainder of grout to the edges of the remaining floor tiles that are still in place. Clean the floor of old adhesive etc. Fix in place replacement tiles, allow adhesive to cure then regrout If you don't want to risk a standard angle grinder, a slower but safer / alternative tool is a multi tool and a 'Heel' diamond blade. this will be slower but the results are the same. What you DON'T do is just smack the damaged tiles with a hammer before removing the grout, this has the definite possibility of the shock wave transferring through the damaged tile through to neighbouring good tiles and chipping / damaging them too Hope this helps, Griff 5 Quote Link to comment Share on other sites More sharing options...
Timbo Posted November 7, 2016 Share Posted November 7, 2016 13 minutes ago, BroadAmbition said: driven up to near to Carlisle to do a huge estimate 'What thy 'as there Mrs is t'much Carlisle!' Quote Link to comment Share on other sites More sharing options...
TheQ Posted November 7, 2016 Share Posted November 7, 2016 12 hours ago, Baitrunner said: Thanks Q. That just means more grass to cut Oi I didn't say that, I'd Dremel ( with face mask, goggles and gloves those cuttings disks are renown for breaking up in use) Dremel the grout out round the edges so that there is no pressure on the adjoining tiles then using a small bolster try to get under the edges of tile to prise them off. Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 7, 2016 Share Posted November 7, 2016 Trying to get under the tiles in the grout lines after removing the grout with a bolster no matter how small is asking for trouble damaging the adjoining tiles - Don't do it, just smack the tiles to be removed in the middle of em good and proper, then you can get under them from the middle of the tile outwards encouraging them to lift rather than shoving them sideways towards their neighbours Griff 6 Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 7, 2016 Author Share Posted November 7, 2016 Thanks Griff. I shoukd have just pm'd you but that seemed too cheeky. I went for the subtle approach!!!! Too subtle for a busy Yorkshireman i will probably start with the dremel as it worked for me cutting out my table deck fittings and it's not as mental as the angle grinder!!! If that takes too long maybe a multi tool will find its way into my workshop this week if you don't hear from me I cocked up and am relaying the whole floor 3 Quote Link to comment Share on other sites More sharing options...
Wildfuzz Posted November 7, 2016 Share Posted November 7, 2016 If you have a router get a couple of cheap TCT bits, and with the proper PPE and dust removal "nibble" away at them, should be no shock waves and fairly accurate. Not what they are designed for but have seen it done to great effect. 1 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 7, 2016 Share Posted November 7, 2016 Bautrunner - what's your location? Griff Quote Link to comment Share on other sites More sharing options...
Baitrunner Posted November 7, 2016 Author Share Posted November 7, 2016 Hi Griff, I'm just outside East Dereham off the A47. ps. Will have my new to me bike on Sunday so will be in the Triumph owners club Wont be as quick as yours though! Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted November 7, 2016 Share Posted November 7, 2016 Mum used to live in N. Elmham. Ok not sure when I'm passing next with the van. Enjoy the steed Griff 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.