Timbo Posted September 24, 2016 Share Posted September 24, 2016 Ah yes...but you were looking with your eyes. Oddly all of my relations on both sides of the family are all under 5'8", my mum just under 5'. Even my paternal great grandfather 'Big' Tim Healy who I'm named after was a little feller at 5'4", so gawd knows where my long shanks came from? But every Yorkshireman, no matter the gap between his toes and his head when he's stood up...is eight feet tall. Next time you see a Yorkshireman walk through a tall archway,through a high door, into a church or under a high bridge, you just watch, cos he will unconsciously duck to avoid hitting his head. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 24, 2016 Author Share Posted September 24, 2016 I think they duck because they heard there was a toll on passing through doorways based upon height, so instinct makes them duck to appear shorter and thus pay a smaller toll. 3 Quote Link to comment Share on other sites More sharing options...
BroadScot Posted September 24, 2016 Share Posted September 24, 2016 You forgot their flat caps, that are not that flat! They add a few extra inches ! 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 25, 2016 Author Share Posted September 25, 2016 A couple of good purchases at the boot fair this morning, a bundle of oak strips and a bundle of softwood strips for £6. plus a whole bundle of construction brass rod and tube for just £10 - bargains, 10 strips of oak strip would be more expensive than all that timber, and those brass bits are about £1 a strip for the cheapest. this has advanced the build somewhat as it saves me some timber preparation. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 25, 2016 Author Share Posted September 25, 2016 well I just had to go out and increase the crew team, so another quick trip to the range, and we now have 5 new crew members. the first rib has been steamed, I gave this 8 minutes, but was a bit slow forming it round the bends, hopefully better next one. then we have a picture of the timber got this morning - now sorted, and waiting for its staking / sorting system to dry and be ready for use. (the 9 sections of cardboard tube will keep the timber from going everywhere). 4 Quote Link to comment Share on other sites More sharing options...
BroadScot Posted September 25, 2016 Share Posted September 25, 2016 We will know which one is Robin by the blue fender in his hand ! 3 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 25, 2016 Author Share Posted September 25, 2016 well an hour is too short to let the wood set after steaming, I steamed a new rib, and the old one was still springing back straight, so I clamped that one on the model, the next one will be given a couple of hours, but I think my previous experience says it needs overnight to dry out properly. off outside to cut some more rib material. 4 Quote Link to comment Share on other sites More sharing options...
FairTmiddlin Posted September 25, 2016 Share Posted September 25, 2016 Have to make the tender to bigger with Nine drunken Sailors Quote Link to comment Share on other sites More sharing options...
grendel Posted September 25, 2016 Author Share Posted September 25, 2016 Ah but those figures I have will be split between the two models. so 4 for each, plus the resin 1 man and his dog. here is the wood storer in situ now keeping the wood tidy, I stripped 3 5mm pine boards into 5x2.5 for the ribs. 2 Quote Link to comment Share on other sites More sharing options...
Wildfuzz Posted September 26, 2016 Share Posted September 26, 2016 Lovely barley twists on the item behind the wood racks........ Quote Link to comment Share on other sites More sharing options...
grendel Posted September 26, 2016 Author Share Posted September 26, 2016 thats a folding table stand, we use it with a big brass top as a spare table when we want to sit around in the lounge for games or chinese takeaway (well we have to as I have nicked the kitchen table as my workshop). 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 26, 2016 Author Share Posted September 26, 2016 tonights work, no pictures as its more of the same really, just another rib steamed and bent. once I have enough I will start gluing them into position. I have come to a decision to just do enough for the first model, as until they are glued in place the ribs are quite delicate, so storage would be a problem. 2 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted September 26, 2016 Share Posted September 26, 2016 Trying to get caught up, just back last night from a riotous assembly afloat for the weekend. Impressed yet again at progress Griff Quote Link to comment Share on other sites More sharing options...
grendel Posted September 27, 2016 Author Share Posted September 27, 2016 a bit of a bum day today, first the vax steam cleaner I have been using to steam my timbers has tripped the electrics - twice - but only while the cooker is on, then two of the timbers I was bending have cracked and split, mind you I am doing the part with the tightest bends, the ribs next to the transom, maybe I will give it one more shot, but the steam cleaner is definately getting replaced with a wallpaper steamer, as then I wont need to keep my finger on the trigger. 2 Quote Link to comment Share on other sites More sharing options...
ZimbiIV Posted September 27, 2016 Share Posted September 27, 2016 When you steam do you spray the wood with water first? It always helps to get the steam get inside the wood. A fine mist spray is what you need. paul Quote Link to comment Share on other sites More sharing options...
grendel Posted September 27, 2016 Author Share Posted September 27, 2016 the big problem is that the steam cleaner doesnt seem to be kicking out as much steam as it used to, it will never last out the remaining ribs I have to steam, time I think to get a better steam source. (wallpaper steamer). Quote Link to comment Share on other sites More sharing options...
grendel Posted September 28, 2016 Author Share Posted September 28, 2016 Ok, after wearing out the steam cleaner, after work today (having safely found an alternate route home due to the M2 being shut) it was a quick pop into B&Q and I now have a wallpaper steamer, this doesnt rely on a finger to keep it going, and is as simple as a large kettle, so not a lot to go wrong. tried it out, it took longer to get steam up, but was a more consistent quantity of steam, 10 minutes and the rib went round the tightest former (transom) a treat. once I have at least one more transom sized rib, i can start installing from the back end. 6 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted September 28, 2016 Share Posted September 28, 2016 Sorted - Well done that man Griff 1 Quote Link to comment Share on other sites More sharing options...
MauriceMynah Posted September 29, 2016 Share Posted September 29, 2016 11 hours ago, grendel said: once I have at least one more transom sized rib, i can start installing from the back end. I refrain from comment 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 29, 2016 Author Share Posted September 29, 2016 On 9/27/2016 at 9:33 PM, ZimbiIV said: When you steam do you spray the wood with water first? It always helps to get the steam get inside the wood. A fine mist spray is what you need. paul No, I admit I dont, I figure the steam pretty much gets in anyway - eventually, the timber usually comes out hot damp and bendy, and I have to admit these curves are very tight, the rest should be easier. Quote Link to comment Share on other sites More sharing options...
grendel Posted September 29, 2016 Author Share Posted September 29, 2016 actually, now I am using the wallpaper steamer, the wood is getting much more flexible in 10 minutes, then its out and quickly wrapped round the former, then wedges fitted to form the exact shape. tonights work, another transom rib steamed, then the first rib put into place and glued, I really need to turn the boat so I have better access now. it needs to be stern on to work both sides - re-organisation of workspace next step, as the steamer will need relocating too. 3 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 29, 2016 Author Share Posted September 29, 2016 Well my workshop is the wrong shape, its not deep enough, but hey, it just about works, and I can now get to both sides easier, the steamer will also stick out, and that is hot while running,plus of course I need to keep a space for steaming ribs around the formers. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted September 30, 2016 Author Share Posted September 30, 2016 Another rib steamed, another one fixed in place, some tidying up starting at the transom. tomorrow will be a trip into wilkinsons in town to pick up a few more 1" G clamps as they fit through smaller gaps for clamping, though some may need grinding narrower to squeeze between ribs next to bulkheads. 5 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted October 1, 2016 Share Posted October 1, 2016 Tis looking proper impressive Griff 1 Quote Link to comment Share on other sites More sharing options...
MauriceMynah Posted October 1, 2016 Share Posted October 1, 2016 Going by another thread, if it were to be an accurate model, it would need to look... "Improper impressive" 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.