andyg Posted September 22, 2022 Share Posted September 22, 2022 3 minutes ago, Mouldy said: Had to read that twice - 670 years ago? Β Did they have GRP then? Doh! Β Yeas, it was called πͺ΅...OK OK I'm going.... Quote Link to comment Share on other sites More sharing options...
andyg Posted September 22, 2022 Share Posted September 22, 2022 Well she's already back at Potter... 1 Quote Link to comment Share on other sites More sharing options...
Smoggy Posted September 22, 2022 Share Posted September 22, 2022 19 minutes ago, andyg said: Well she's already back at Potter... Towed or under own power? Quote Link to comment Share on other sites More sharing options...
Hylander Posted September 22, 2022 Share Posted September 22, 2022 8 minutes ago, Smoggy said: Towed or under own power? You having a laugh? Quote Link to comment Share on other sites More sharing options...
oldgregg Posted September 22, 2022 Share Posted September 22, 2022 I think the photo might be a little misleading because of the frayed edges of the GRP where it has been chopped out? If you look at the thickness along the right edge it's fairly decent. Certainly the C40 / C45 were laid up heavier than a lot of stuff was at that time. But yeah, boats built in the 70's / 80's are much thicker than what is being built now. It's not just a Broads thing, I know the likes of Princess have used various techniques to achieve a much thinner layup than they ever used to. 2 Quote Link to comment Share on other sites More sharing options...
andyg Posted September 22, 2022 Share Posted September 22, 2022 27 minutes ago, Smoggy said: Towed or under own power? Towed I would imagine, that said with a bit of tinkering around I'm sure that engine would fire up.Β Quote Link to comment Share on other sites More sharing options...
Smoggy Posted September 22, 2022 Share Posted September 22, 2022 15 minutes ago, Hylander said: You having a laugh? Nope, as long as it wasn't running as it was submerged I recon it's doable,Β likely need a spare battery and not be charging but pump out sump and refill, remove glow plugs and spin over till water is out, refit glow plugs and start. Run it till properly hot for a while and change oil again with new filter. Pump out gearbox and refill,Β do it again when back at base. Probably take less time than towing by time you factor in shuffling tow boats and returning them to the right place and by the time it's back at base you know if the engine is OK. 2 Quote Link to comment Share on other sites More sharing options...
andyg Posted September 22, 2022 Share Posted September 22, 2022 The boat settled on its port side, the engines on these boats are in the stern at midships so it's highly unlikely the engine was full submerged in water.But I'm with Smoggy on this. I totally believe that engine would run again with a bit of work.. 1 Quote Link to comment Share on other sites More sharing options...
Smoggy Posted September 22, 2022 Share Posted September 22, 2022 39 minutes ago, andyg said: I totally believe that engine would run again with a bit of work.. Or better mechanics... Quote Link to comment Share on other sites More sharing options...
Smoggy Posted September 22, 2022 Share Posted September 22, 2022 I must add to my previous posts about the engine that I am assuming it's an old school mechanical injection and not a modern common rail with ECU, in which case it has a good chance of being dead as a very dead thing with added dead bits if the electrics are fried. 1 Quote Link to comment Share on other sites More sharing options...
oldgregg Posted September 22, 2022 Share Posted September 22, 2022 1 hour ago, Smoggy said: I must add to my previous posts about the engine that I am assuming it's an old school mechanical injection and not a modern common rail with ECU, in which case it has a good chance of being dead as a very dead thing with added dead bits if the electrics are fried. It'll be an old school engine, yes. There are very few common rail engines in Broads cruisers (though I do know of one yard doing it). Assuming it's not hydrolocked it'd just be a case of getting any water out and getting it going again. Quote Link to comment Share on other sites More sharing options...
andyg Posted September 22, 2022 Share Posted September 22, 2022 27 minutes ago, oldgregg said: It'll be an old school engine, yes. There are very few common rail engines in Broads cruisers (though I do know of one yard doing it). Assuming it's not hydrolocked it'd just be a case of getting any water out and getting it going again. The one's I've seen fitted look quite old lol.. Quote Link to comment Share on other sites More sharing options...
oldgregg Posted September 22, 2022 Share Posted September 22, 2022 They are, yeah. Mostly big old Nannis and the prop never seems to be matched to the powertrain - It's easy to use too many revs and make them cavitate when manoeuvring. Lovely boats and generally they handle quite well but I'd be changing the prop if I bought one. When we hired Dominica, we figured out the best approach was to set the throttle and wait a goodly while for something to happen. The first-gen Connoisseurs seemed to have the same problem with cavitation too. I'm guessing they might have been 'modified' when they came back from france. 2 Quote Link to comment Share on other sites More sharing options...
andyg Posted September 22, 2022 Share Posted September 22, 2022 I've looked at hiring richardsons one it looks smart and very reasonably priced.I have hired one from CC before and liked it very much. We had a problem with the engine on the one we had.It kept cutting out/ stalling if you moved the morse control to quickly. It packed up at Acle Bridge and the guys from bridgecraft had to rescue us lol. I've seen inside quite a few of the engine bays of the ones at woods and I would say there quite old engines.. Quote Link to comment Share on other sites More sharing options...
BrundallNavy Posted September 22, 2022 Share Posted September 22, 2022 When I worked for a large hire yard we had a yacht sink at Great Yarmouth, I got the job of cleaning it out lots of black stinking mud. It was back in hire in just over two weeks so it can be done. Β 1 Quote Link to comment Share on other sites More sharing options...
Wonderwall Posted September 22, 2022 Share Posted September 22, 2022 Glad to hear the boat is back homeπ. I have hired this actual boat a couple of times , so, of course feel as if I have some attachment to it . I know very little about the upkeep of such boats, but I would imagine HW easily have the skill and tools to put her back in action. I also , maybe wrongly, assumed they would take her home by road? It does make you realise, that no matter how experienced ( or not) you are at boating, things can go wrong very quickly. A wee bit of bad luck , and it can all go pete tongπ₯. No different than driving our motors I suppose. The main thing is, the crew live to tell the tale, anything lost , can be replaced. Β Oh, and off topic, but regarding another thread that has been on lately, I think this is still a very friendly forum, with the vast majority of posters being respectful, helpful and well informed. Hats off to them who run it for us , I say. Long may it continue π 8 3 Quote Link to comment Share on other sites More sharing options...
stumpy Posted September 24, 2022 Share Posted September 24, 2022 I'm sure I remember reading some years ago, possibly in another place, that the gabions along the New Cut were shifting into the channel. I think, at the time, it was blamed on large twin-engine jobbies possibly from Brundall hammering up and down. 1 Quote Link to comment Share on other sites More sharing options...
Meantime Posted September 24, 2022 Share Posted September 24, 2022 Word from the Rhond, well some of the first that got there anyway, is that the boat didn't hit a gabion basket down the Cut. It didn't hit the concrete buttress under the bridge. It hit the edge of the bank where it sank whilst taking avoiding action from another boat. Where it sank there is a large lump that sticks out that was submerged due to the high water. I believe it is now marked with sticks. 1 1 Quote Link to comment Share on other sites More sharing options...
marshman Posted September 24, 2022 Share Posted September 24, 2022 That sounds about right - never actually looked like the actual New Cut to me other than the very bottom end and thats some way from the gabions I think. 1 Quote Link to comment Share on other sites More sharing options...
Bikertov Posted September 24, 2022 Share Posted September 24, 2022 On 22/09/2022 at 19:53, BrundallNavy said: When I worked for a large hire yard we had a yacht sink at Great Yarmouth, I got the job of cleaning it out lots of black stinking mud. It was back in hire in just over two weeks so it can be done. Β Is that why you don't work for a large hire yard anymore ... 1 Quote Link to comment Share on other sites More sharing options...
Meantime Posted September 24, 2022 Share Posted September 24, 2022 11 minutes ago, marshman said: That sounds about right - never actually looked like the actual New Cut to me other than the very bottom end and thats some way from the gabions I think. Yes, the gabions are Reedham side of Haddiscoe Bridge. The boat went down right at the end of the New Cut where it joins The Waveney. Word is a yacht came around the corner from downstream of the junction on The Waveney and entered The New Cut, and the boat moved to its Starboard in avoidance and hit the unseen obstruction obscured by the very high water. Quote Link to comment Share on other sites More sharing options...
FlyingFortress Posted September 24, 2022 Share Posted September 24, 2022 That makes sense to me. π Quote Link to comment Share on other sites More sharing options...
stumpy Posted September 24, 2022 Share Posted September 24, 2022 Meantime and others - thanks for the clarification, I've been afloat for a week ducking into and out of signal so not seen the previous gen. Quote Link to comment Share on other sites More sharing options...
ranworthbreeze Posted September 24, 2022 Share Posted September 24, 2022 Gabions used in water is not a great idea even if stainless steel was used and on the New Cut is not the best form of bank forming. Β Β Quote Link to comment Share on other sites More sharing options...
addicted Posted September 24, 2022 Share Posted September 24, 2022 Sometime back in the 90s a group of girl hirers managed to sink a fairly large boat outside what was in those days the Cambridge rowing team boat house on the RGO on the main drag through Ely. They had apparently tried to turn round backing up to the corner of the wall that flanked the slipway Because the water was exceptionally high they were unable to see the acute angle which was submerged. A massive hole the size of a dinnerplate was punched into the stern, and she went down pretty quickly. The story went that one of the girls was trapped in the v berth and had the presence of mind to kick out the front screen and escape. Once the boat was resting on the bottom they apparently gathered all their belongings and promptly went home. Their car was only a few minutes walk away as the hire yard was just a few hundred yards upstream from where they sank. We watched the refloating the next morning, fascinating. Β Carole Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.