CambridgeCabby Posted April 5, 2020 Share Posted April 5, 2020 And just for Griff a nice Rose Emblem on the shirt , since the t shirt is white it will have to be a red one Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted April 6, 2020 Share Posted April 6, 2020 And just for Griff a nice Rose Emblem on the shirt , since the t shirt is white it will have to be a red one Really? Peter as we all know is a stickler for getting everything just right and factual so I doubt it Griff 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 6, 2020 Author Share Posted April 6, 2020 cant you see the white rose on the white tee shirt, though at that scale the yellow centre parts look just like egg stains from his breakfast 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 6, 2020 Author Share Posted April 6, 2020 ok lets get on with painting tiny details, to make any figure realistic there is a minimum level of detail that works, part of this of course is the question of putting the eyes in, this is a trick i learned painting 25mm figures, so with the very tip of a small brush, you just dot the whites of the eyes in, on 25mm figures this would be a 0000 brush (about 10 hairs) then once we have the whites of the eyes we need a pupil, on a 25mm figure i would pluck a single hair for this and just barely dip it in the paint, for this figure its a bit bigger, so i chose a bamboo skewer for this job, just barely dipped into the brown paint, and bingo, you do have to get these positioned right, theres nothing worse than giving the figure a squint 2 Quote Link to comment Share on other sites More sharing options...
Upcycler Posted April 6, 2020 Share Posted April 6, 2020 I appreciate your skills as a model maker, but the first picture he looks stoned and the last one it looks like he's had a heavy Friday night. Unless of course this model is life like 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 6, 2020 Author Share Posted April 6, 2020 well its after the morning rum with a dash of coffee if thats what you mean. 1 Quote Link to comment Share on other sites More sharing options...
ranworthbreeze Posted April 7, 2020 Share Posted April 7, 2020 Hello Grendel for Griff's sake I hope that is not a true to life figure Regards Alan Quote Link to comment Share on other sites More sharing options...
JennyMorgan Posted April 7, 2020 Share Posted April 7, 2020 Where's his hat? Quote Link to comment Share on other sites More sharing options...
grendel Posted April 17, 2020 Author Share Posted April 17, 2020 well today saw a nice day outside, one of the first essentials of painting, so model #2 was moved to the new workshop area, masking up and removing things that did not require paint was the order of the day, Once everything was masked up the first light coat of white was applied, this will show up any imperfections in the resin and fibreglass coat that went on before. then it was the turn of the cabin roofs, everything had to be either removed or masked up, fortunately the hinged windscreen parts come off easily by removing the hinge pin. Handrails were removed and labelled so they can o back in the same way they came out. roof parts recieved a first coat of filling primer, they will later get another and when thoroughly dry a sanding. The hull has then had a second thin coat of white, i can already see there are some areas that will need attention. 7 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted April 17, 2020 Share Posted April 17, 2020 Great work once again Griff Quote Link to comment Share on other sites More sharing options...
grendel Posted April 18, 2020 Author Share Posted April 18, 2020 So as i was asking whether to attach the rubbing stakes before or after painting and was advised that after would be best, i needed to convert some timber to enable them to be cut, so my big block of teak was brought out and some 5mm thick planks were cut out of the large piece, and last night run through the thicknesser to plane the surfaces, so today I thought i would show you how larger pieces of timber are made down to the sizes needed for the model. 3 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 18, 2020 Author Share Posted April 18, 2020 So Having cut out the rubbing strakes two have now been sanded down and the outer edges rounded off slightly, meanwhile the cabin roofs have received a first coat of white and the hull has been given a preliminary rubbing down. 3 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 19, 2020 Author Share Posted April 19, 2020 a slight problem has been observed this morning, between getting up and yoga i flashed a new coat of paint over the areas that had been sanded back, and while the original coat went on perfectly, this time a few areas have reacted and crinkled, so i am now looking at whether sanding back the crinkle and overspraying is the answer or whether i will need to take it right back to the resin coat, i have an inkling that the paint is reacting to the freshly exposed by sanding resin surface, lets see if we can pull this back, now to do my sunday tasks before going back to model work 2 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 19, 2020 Author Share Posted April 19, 2020 looking at the crackle, i have sanded it back and over coated it with another couple of light dustings of paint, hmm the problem is still there, i will give it overnight to dry off properly then try once again to flat it back and build a decent coating of paint to seal over the problem areas. worst case will be hitting it with acetone to remove the paint thats on there and start again. 3 Quote Link to comment Share on other sites More sharing options...
JanetAnne Posted April 19, 2020 Share Posted April 19, 2020 Got any water based primer mate? Anything solvent based may continue to react once the sealed surface you began with has been disturbed. Quote Link to comment Share on other sites More sharing options...
grendel Posted April 19, 2020 Author Share Posted April 19, 2020 the stuff that reacted was an acrylic water base primer, the other stuff i have is a resin based paint Quote Link to comment Share on other sites More sharing options...
ZimbiIV Posted April 19, 2020 Share Posted April 19, 2020 I had the same problem with the model I am building now. I was very happy with the finish then decided to put 3rd coat on, oops! I had to rub the hull down (not easy on a 1 metre long hull). Did this twice until I realised the 3rd layer of acrylic was the problem then went back to old fashioned oil based paint, no problem at all just had to wait longer for each coat to dry. paul 1 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 19, 2020 Author Share Posted April 19, 2020 The cabin roofs however have behaved themselves when painting, so they are done, ready to have fittings put back once the paint has had 24 hours to cure. 4 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 20, 2020 Author Share Posted April 20, 2020 well 12 hours to cure anyway, slow start today, checked out the cracle spots on the hull, repeated coats of the resin based paint is slowly filling the crackle areas, i think ts going to be a case of build up a reasonable thickness , allow it to cure properly then sand back and recoat. in the mean time, i have been cleaning up the paint that got past the masking on the rear cabin roof, and refitting the roof fittings, the mast and handrails. now i know that the cover strips that cross the roof are actually varnished timber, but at present they can stay white, if i decide to make them varnished timber it will be just a few seconds work to sand the paint off and varnish them. 2 Quote Link to comment Share on other sites More sharing options...
BroadAmbition Posted April 20, 2020 Share Posted April 20, 2020 That must be the first time I have witnessed you not following the full size version to the letter. If you do decide to varnish them as per the one currently abandoned in the Wetshed, it would be easier to do before you fit the handrails - Hint ! They do look proper good all the same Griff 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 20, 2020 Author Share Posted April 20, 2020 Charlie, in all probability i will varnish them, and the handrails are pretty easy to remove, they will probably come off for the wooden rails to be varnished and trimmed to length anyway. but really the paint should have a real chance to cure off hard before it is sanded off anyway, otherwise its just going to be a problem. (it was easier to paint and sand off than it would have been to try and mask it off anyway). 2 Quote Link to comment Share on other sites More sharing options...
grendel Posted April 20, 2020 Author Share Posted April 20, 2020 Front cabin roof fittings reassembled 3 Quote Link to comment Share on other sites More sharing options...
Ray Posted April 20, 2020 Share Posted April 20, 2020 Looks great! I lost track on where you are with the other model, are you keeping them up to date with each other or forging ahead with this one now? Quote Link to comment Share on other sites More sharing options...
grendel Posted April 20, 2020 Author Share Posted April 20, 2020 concentrating on this one for the moment. though i will probably hop to the older one to try anything new. 1 Quote Link to comment Share on other sites More sharing options...
Ray Posted April 20, 2020 Share Posted April 20, 2020 That makes sense 👍 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.